                     The BitTorrent Protocol Daemon

                                README

                           btpd version 0.13


Contents
1               Introduction
1.a               What is btpd?
1.b               The programs
1.c               The btcli commands
2               Using btpd
2.a               Introduction
2.b               Starting btpd
2.c               Examples
2.d               Troubleshooting
3               Building
3.a               Requirements
3.b               Standard build
4               Upgrade notes
4.a               btpd 0.12

1. Introduction

1.a What is btpd?

  btpd is a bittorrent client consisting of a daemon and client commands,
  which can be used to read and/or manipulate the daemon state. The daemon
  is capable of running several torrents simultaneously and only uses one
  tcp port. It's fairly low on resource usage and should be perfect for
  file distribution sites. Efficient downloads and ease of use makes this
  client a good choice for the casual user as well.

1.b The programs

  btpd consists of the following programs:
  * btpd     - The bittorrent client.
  * btcli    - Command line interface to btpd.
  * btinfo   - Shows information from a torrent file.

  All programs accept the "--help" option.

1.c The btcli commands

  The btcli utility has several different modes of operation. One of the
  following commands must be specified when running btcli:
  * add      - Add torrents to btpd.
  * del      - Remove torrents from btpd.
  * kill     - Shut down btpd.
  * list     - List torrents.
  * start    - Activate torrents.
  * stat     - Display stats for active torrents.
  * stop     - Deactivate torrents.

2. Using btpd

2.a Introduction

  To start sharing a torrent with btpd, the torrent needs to be added to
  btpd. This is done with 'btcli add'. When you add a torrent btpd auto-
  matically (if you didn't specify otherwise) starts to share the torrent
  and download any missing data. The content directory you specify when
  adding a torrent doesn't need to exist; it will be created by btpd.

  You can see which torrents have been added to btpd with 'btcli list'.
  The list command also displays a number for each added torrent. This number
  can be used to specify the target torrent for the btcli commands, so you
  don't have to keep the torrent file once you've added it.

  The up- and download progress can be followed by using the 'btcli stat'
  command. Both the list and stat commands use the following indicators to
  display the state of a torrent:
  +     the torrent is starting. This may take time if btpd needs to test
        the content of this torrent or one started before it.
  -     the torrent is being stopped. May take time if the tracker is
        unresponsive. 
  I     the torrent is inactive.
  S     btpd is seeding the torrent.
  L     btpd is leeching the torrent.

  You can stop an active torrent with 'btcli stop' and, of course,
  start an inactive torrent by using 'btcli start'.

  The 'btcli del' command should only be used when you're totally finished
  with sharing a torrent. The command will remove the torrent and its
  associated data from btpd. It's an escpecially bad idea to remove a not
  fully downloaded torrent and then adding it again, since btpd has lost
  information on the not fully downloaded pieces and will need to download
  the data again.

  To shut down btpd use 'btcli kill'. Don't forget to read the help for each
  of btcli's commands.

2.b Starting btpd

  NOTE: You should only need one instance of btpd regardless of how many
  torrents you want to share.

  To start btpd with default settings you only need to run it. However,
  there are many useful options you may want to use. To see a full list
  run 'btpd --help'. If you didn't specify otherwise,  btpd starts with
  the same set of active torrents as it had the last time it was shut down.

  btdp will store information and write its log in $HOME/.btpd. Therefore
  it needs to be able to write there during its execution. You can specify
  another directory via the '-d' option or the $BTPD_HOME variable.

  I recommend specifiying the maximum number of uploads. Bittorrent employs a
  tit for tat algorithm, so uploading at good rates allows for downloading.
  Try to find a balance between uploads/outgoing bandwidth and the number of
  active torrents.

2.c Examples

  Start btpd with all options set to their default values.
  # btpd

  Start btpd and make it listen on port 12345, limit outgoing bandwidth to
  200kB/s, limit the number of peers to 40 and not start any torrents that
  were active the last time btpd was shut down.
  # btpd -p 12345 --bw-out 200 --max-peers 40 --empty-start

  Display a list btpd's torrents and their number, size, status, etc.
  # btcli list

  Same as above, but only for torrent 12 and my.little.torrent.
  # btcli list 12 my.little.torrent
  
  Same as above but only for active torrents.
  # btcli list -a

  Add foo.torrent, with content dir foo.torrent.d, and start it.
  # btcli add -d foo.torrent.d foo.torrent

  Same as above without starting it.
  # btcli add --no-start -d foo.torrent.d foo.torrent 

  Start bar.torrent and torrent number 7.
  # btcli start bar.torrent 7

  Stop torrent number 7.
  # btcli stop 7

  Stop all active torrents.
  # btcli stop -a

  Remove bar.torrent and it's associated information from btpd.
  # btcli del bar.torrent

  Display a summary of up/download stats for the active torrents.
  # btcli stat

  Display the summary once every five seconds.
  # btcli stat -w 5

  Same as above, but also display individual stats for each active torrent.
  # btcli stat -w 5 -i

  Shut down btpd.
  # btcli kill

2.d Troubleshooting

  If btpd has shut down for some unknown reason, check the logfile for
  possible clues.

3. Building

3.a Requirements

  You should have a *BSD, Linux or sufficiently similar system.

  Make sure you have recent versions of the following software:
  * OpenSSL   - Get at <URL:http://www.openssl.org/>

  You also need a c99 compiler. A non antique GCC should do.

3.b Standard build

  # ./configure
  # make
  # make install

  See './configure --help' for available build options if the above fails.

4. Upgrade notes

4.a btpd 0.12

  The layout of the torrents directory in the btpd directory has changed
  since previous versions. Please remove the torrents directory before
  running 0.12 or later.
